Synchronization issues
Unblock a slow or stuck import, understand the error message on the card and restart automatic sync.
This page helps when synchronization isn't going well. The history import no longer moves forward, the store card shows an error, or automatic sync has stopped.
Always start by reading the card. Open Settings, then the Integrations tab, and look at your store's card in the E-commerce category. The dot color, the Last sync date and the text of any box tell you what to do. Each state is detailed in Sync status.
The history import seems slow
A first import can take several hours on a store with many orders. As long as the dot blinks blue, the import is working, even if the percentage barely moves. The last percentages often take the longest, because Fullmetrix checks the data and calculates totals after copying it.
You can close the page. The import keeps going without you. Meanwhile, avoid disabling the module, reconnecting the store or clicking Disconnect. See Historical import.
The card shows a red error
A red dot and a red box mean the last attempt failed. The Sync button is replaced by Resume and Reset.
Read the message
The text in the box comes from your store or from Fullmetrix. It usually states the cause. Copy it, you'll need it if you have to write to us.
Fix the cause
The table below gives the fix for the most common messages. If you restart without fixing it, the same failure happens again.
Click Resume
Resume restarts the sync and keeps the progress already made. The dot turns blue. If it turns green again, you're done.
Reset as a last resort
If Resume isn't offered or isn't enough, click Reset, then confirm in the Reset sync? window. Progress starts again from zero, but orders already imported are kept.
The most common causes
| What the message says | Likely cause | What to do |
|---|---|---|
| It mentions Cloudflare or an IP Access Rule | Cloudflare's anti-bot protection blocks our calls | Follow Cloudflare and firewalls |
| 403, access denied, forbidden | A firewall, security extension or country block refuses our calls | Allow Fullmetrix, see Cloudflare and firewalls |
| 401, unauthorized | The module no longer recognizes the connection, often after a reinstall | Check the module is enabled and linked with the code from the card |
| 404, not found | The module is disabled or uninstalled, or the store address changed | Enable the module again. If the address changed, write to us |
| 429, too many requests | Your hosting or firewall limits the number of calls | Allow the Fullmetrix address in the rate limiting rule |
| 500, 502, 503, timeout | Your store returned an error or didn't answer in time | Check the site is online. On busy hosting, try again later |
Platform-specific errors are covered on the PrestaShop, WooCommerce, Shopify, Magento and Sylius troubleshooting pages.
Automatic sync is disabled
An orange dot and the "Auto-sync disabled after N consecutive errors" box mean Fullmetrix stopped its automatic checks. This happens when several attempts in a row fail and none has succeeded in the last 24 hours.
Fix the cause first. It's almost always a store Fullmetrix can no longer reach, because of a firewall, a disabled module or a site that is offline. Then click Resume, or Reset if Resume isn't offered. The box mentions the Sync button, but in this state these two buttons show in its place.
Once a sync succeeds again, automatic checks resume and Fullmetrix catches up on everything that changed since the last successful sync.
The Sync button is greyed out
Only one sync can run at a time for a store. If the button is greyed out and the dot blinks blue, a sync is already running. Wait for it to finish. If you just clicked, reload the page after a few minutes to see the new state.
The last sync date no longer moves
Normally, the Last sync date is less than an hour old, because Fullmetrix checks your store every 15 minutes. If it's several hours old while the dot is green, the latest checks are failing without blocking the card yet.
- Click Sync and see whether an error message appears.
- Check in your store that the Fullmetrix module is still enabled.
- Check that no new protection was turned on for your site.
- On Magento, check that scheduled tasks (cron) run on your server. Without them, changes only arrive during Fullmetrix's checks.
Before writing to us
If the problem persists, send us the platform, the store address, the exact text of the box, the Last sync date and what you already tried. Don't include a password or the Connection code. See Contact support.
Don't disconnect the store to retry
Disconnect deletes the connection and every imported order, with no way back. You would then have to redo the whole history import. Resume and Reset are enough in every case described here.