fullmetrixDocs

Cloudflare and firewalls

Allow Fullmetrix in Cloudflare or in your store's firewall so synchronization resumes, without lowering your site's protection.

To read your orders, Fullmetrix calls the module installed on your store. A firewall or an anti-bot protection can mistake that call for an attack and block it. Your site opens normally in your browser, yet the sync fails. This page shows you how to recognize it and how to allow Fullmetrix, step by step.

A firewall is a filter in front of your site that decides which visits get through. Cloudflare is the most common one. Your hosting provider or a security extension (Wordfence, Sucuri, a PrestaShop security module) can add another.

Who this applies to

This page applies to PrestaShop, WooCommerce, Magento and Sylius stores. With these platforms, Fullmetrix fetches the data from your server, so your firewall sees our calls.

Shopify stores are not affected. Fullmetrix reads their data through Shopify, without going through your domain name or your Cloudflare.

Recognize a block

Open Settings, then the Integrations tab, and look at your store's card in the E-commerce category.

When Cloudflare blocks the sync, Fullmetrix detects it and shows a full red message on the card. It mentions the Cloudflare anti-bot protection, asks you to create an IP Access Rule and gives the IP address to allow. This message is currently shown in French, whatever your interface language. The dot next to the platform name turns red.

Other signs point to a firewall, even without the Cloudflare message.

  • The error message mentions access denied, 403, 429 or a timeout.
  • After several failures, the card shows "Auto-sync disabled after N consecutive errors".
  • The problem started right after you turned on a protection, changed hosting provider or set up country blocking.

To read the other card states, see Sync status.

Find the address to allow

Fullmetrix calls your store from a single fixed IP address. You'll find it in two places.

  • In the red message on the card, when Cloudflare is the cause.
  • On our public FullmetrixSync bot page, section How to identify it, line Source IP address.

That public page also gives the name our calls present (the User-Agent FullmetrixSync/1.0) and the paths on your store that we call. You can forward it as is to your hosting provider or agency.

Allow Fullmetrix in Cloudflare

The rule to create is called an IP Access Rule. It tells Cloudflare to let one specific address through, without changing anything for your other visitors. It's the only method that also gets past Bot Fight Mode on Cloudflare's Free plan.

Open the site in Cloudflare

Sign in to your Cloudflare dashboard at dash.cloudflare.com, then click your store's domain in the list of sites.

Go to IP Access Rules

In the left menu, open Security, then WAF, then the Tools tab. The IP Access Rules section is on that page.

If your dashboard shows the newer layout, open Security then Security rules, click Create rule and choose IP access rules.

Fill in the rule

Fill in the rule form.

Cloudflare fieldValue to enter
ValueThe Fullmetrix IP address, copied from the card message or the FullmetrixSync bot page
ActionAllow
ScopeThis website, to limit the rule to the store's domain
NotesFullmetrix, so you can find the rule later

Then click Add. The rule appears in the list below.

Restart the sync

Go back to Fullmetrix and open Settings, then Integrations. If the store card shows an error, click Resume to continue from where the import stopped, or Reset if Resume isn't offered. If the card shows no error, click Sync.

The dot turns blue during the sync, then green. The Last sync line shows the new date.

A custom WAF rule is not enough on the Free plan

On Cloudflare's Free plan, a custom firewall rule does not bypass Bot Fight Mode. Only an IP Access Rule does. If you already created a custom rule for Fullmetrix and the block persists, add the IP Access Rule.

Check in Cloudflare that our calls get through

In Cloudflare, open Security, then Events. Filter on the Fullmetrix IP address. Once the rule is in place, our calls should show as allowed, no longer blocked or challenged. If blocked events still appear, note the name of the rule that blocks them, that's the one to adjust.

Other Cloudflare settings that can block

An IP Access Rule set to Allow usually gets past every check. If the block persists, check these settings one by one in your Cloudflare dashboard.

  • Under Attack mode, which challenges every visit.
  • A rate limiting rule that blocks after a certain number of calls. During the history import, we make many calls in a short time.
  • Country blocking, if your store refuses visits from abroad. Our calls don't necessarily come from the same country as your store.

Allow Fullmetrix in another firewall

The principle is the same everywhere. You allow the Fullmetrix IP address, without turning off protection for the rest of the site.

Where the firewall livesWhat to do
A WordPress extension (Wordfence, Sucuri, iThemes Security...)Add the Fullmetrix IP address to the extension's allowlist
A PrestaShop or Magento security moduleAdd the IP address to the module's allowlist
Your hosting provider's firewall (ModSecurity or a provider-specific one)Ask your provider's support to allow the Fullmetrix IP address, and send them the link to the FullmetrixSync bot page
Country blocking or an address blocklistCheck that the Fullmetrix address isn't in it

If you prefer a narrower rule, limit the allowance to the paths the module uses. They're listed on the FullmetrixSync bot page, section Where it connects, for example /wp-json/fullmetrix/v1/ for WooCommerce or /module/fullmetrixconnector/api for PrestaShop.

Don't turn off all protection

Turning off Cloudflare or the firewall for the whole site exposes your store. A rule that only allows the Fullmetrix address is enough, and the rest of your visitors stay protected.

Password-protected store

If your whole store asks for a username and password before it displays (htaccess protection, common on staging stores), our calls are refused. Write to us through Report a bug or at [email protected], without putting the password in the message. We'll tell you how to proceed. See Contact support.

If nothing changes

If the sync still fails after adding the rule, send us the text of the red message on the card, the date of the last attempt and the name of your firewall or hosting provider. A screenshot of the rule you created also helps.

See also

On this page